Views: 0 Author: Site Editor Publish Time: 2026-11-13 Origin: Site
How long a solar mounting structure lasts depends mostly on its corrosion protection, and the right choice depends on the site: inland dry, coastal, industrial, or hot and humid. Hot-dip galvanized steel, zinc-aluminum-magnesium (ZAM) coated steel, and aluminum are the most common options, and each has its own strengths and weak points. Corrosion usually starts at cut edges, welds, holes, fasteners and contact points rather than on the flat surface. This guide explains where corrosion begins, compares the common options, and lists what to ask your supplier. It does not give service-life figures, because those depend on the site, the coating and the standard used.
Cut edges and drilled holes. Cutting or drilling after coating exposes bare steel.
Welds. Welding burns off the coating nearby, so welded parts need re-protection or should be welded before galvanizing.
Fasteners. Bolts, nuts and washers are small parts with thin protection, and they are often the first to show rust.
Ground contact. Where posts enter soil or concrete, moisture, salts and chemicals attack the surface.
Dissimilar metals. Aluminum touching carbon steel, or steel touching stainless hardware, can corrode faster at the contact point, especially when wet.
Trapped water and dirt. Open-top sections, overlaps and gaps hold moisture and speed up corrosion.
Option | What it is | Strengths | Limits to check |
|---|---|---|---|
Hot-dip galvanized steel | Fabricated steel parts dipped in molten zinc | Coating covers the whole part, including inside corners; widely used for ground mounts | Heavy parts and large sizes need a suitable bath; white rust can form in storage; coating suits some environments better than others |
Zinc-aluminum-magnesium (ZAM) coated steel | Steel sheet or coil with a zinc-aluminum-magnesium coating | Often chosen where better corrosion resistance than ordinary zinc is wanted, including at cut edges | Cut edges still need checking; confirm coating grade and weight with the supplier |
Pre-galvanized steel | Sheet or coil galvanized before forming | Smooth surface, suits light sections and indoor or mild conditions | Cut edges and holes are bare; usually not the first choice for harsh sites |
Aluminum | Aluminum alloy profiles | Light weight; forms its own surface oxide; common for roof systems | Lower stiffness and larger expansion than steel; galvanic risk with steel fasteners; confirm alloy and finish |
Environment | What to watch |
|---|---|
Inland, dry | Corrosion pressure is usually lower, but ground contact and fasteners still matter |
Coastal or near salt water | Airborne chlorides attack coatings and fasteners; ask for site-specific advice on coating and hardware |
Industrial or polluted air | Acidic or chemical deposits can shorten coating life; check the local conditions |
Hot and humid, or farmland | Long wet periods, and fertilizer or irrigation water near posts |
Saline, alkaline or acidic soil | Underground parts need special attention; soil tests help |
Classifying the site by a recognized corrosivity scheme and agreeing the protection with the supplier and the designer is better than choosing by price alone. The specification and local conditions should decide the final choice.
Fasteners. State the material and coating of bolts, nuts and washers. A good structure with weak hardware will still rust.
Touch-up after cutting or drilling on site. Agree a repair method, and keep a supply of repair material on site.
Welds. Ask whether welding is done before or after coating, and how weld areas are protected.
Storage and transport. Bundled galvanized parts that get wet can develop white rust. Ask about packing and keeping parts dry.
Dissimilar-metal contact. Use suitable isolation or compatible hardware where aluminum meets steel.
Drainage. Avoid shapes and details that trap water.
Which coating or material is quoted for each part: posts, beams, rails, brackets and fasteners?
Which standard, and which edition, does the coating follow?
Can the supplier provide coating thickness records or test reports for the batch?
How are cut edges, holes and welds protected?
What are the fasteners made of, and how are they coated?
How are the parts packed to avoid moisture damage in shipping?
What does the warranty cover, and what conditions does it assume?
Choosing by price only. A cheaper coating on a harsh site can cost more in replacement later.
Specifying the structure but not the fasteners. Hardware is often where corrosion starts.
Ignoring cut edges and holes. Bare steel at these points is the usual starting point.
Mixing metals without isolation. Aluminum and carbon steel in wet contact can corrode quickly.
Not naming the standard. "Galvanized" alone does not say how much coating there is or how it was tested.
Treating the warranty years as a guarantee of performance. Read what it covers and the conditions behind it.
Solar mounting corrosion protection is about the whole structure, not just the main sections: the coating or material, the cut edges and welds, the fasteners, and the ground contact. Hot-dip galvanized steel, ZAM coated steel, pre-galvanized steel and aluminum each fit different sites. Describe your site, name the standard you expect, and ask for the coating records and the fastener details, so the quotation covers what will actually protect the system. For how corrosion shows up during use, see our guide to solar mounting inspection and maintenance.
Neither is better everywhere. Hot-dip galvanized steel is widely used for ground mounts where strength and span matter. Aluminum is lighter and common on roofs, but it is less stiff and needs care at contacts with steel. The right choice depends on the structure, the loads and the environment.
Not automatically. ZAM coatings are often chosen where more corrosion resistance than ordinary zinc is wanted, but the result depends on the coating grade and weight, the part, and the site. Ask for the coating details and compare on the same basis.
Bare steel at cut edges and holes is a common starting point for corrosion, so repairing them is good practice, particularly in damp, coastal or polluted conditions. Agree the repair method with your supplier and the designer.
Planning a solar project and need a corrosion-protection plan for your site? Browse our ground, roof and carport mounting systems, or contact us with your location, environment and standard requirements, and we will reply with a quotation and the questions we still need answered.
Whatsapp: +86-18823394830