Views: 0 Author: Site Editor Publish Time: 2026-11-06 Origin: Site
A solar mounting system is meant to last for decades outdoors, so it needs a simple inspection routine: a check soon after installation, a routine check each year, and an extra check after severe weather. The main items are foundations and posts, rails and beams, bolts and clamps, earth connections, coating and corrosion, and the area under and around the array. Most problems are cheap to fix when found early, and expensive when they are found after a failure. This guide lists what to check, how often, what matters in different climates, and how to record and act on what you find.
Solar structures work in harsh conditions. Wind makes them vibrate, temperature changes make the metal expand and contract every day, and rain, dust, and salt wear at the coating. Over time, bolts can loosen, coatings can break, ground can settle, and earth connections can degrade. None of this is unusual, and none of it shows up in the power output until it has become a bigger problem. A regular look at the structure is the cheapest way to protect the modules and the investment.
Part | What to look for | What counts as a problem |
|---|---|---|
Foundations and posts | Position, tilt, cracks, soil washed away around piles, frost or settlement | A post that has moved, tilted, or lost support from the soil |
Beams, rails, and purlins | Straightness, bending, dents, cracks near joints | Visible sag, deformation, or cracking |
Bolts, nuts, and clamps | Tightness, missing parts, marks showing movement | Loose or missing fasteners, or clamps that have shifted |
Module clamps and edges | Clamp position and grip, module movement, damage at the frame | Loose clamps, modules that have moved, frame damage |
Earthing and bonding | Connections tight and clean, cables intact, continuity across joints | Loose, corroded, or broken connections |
Coating and corrosion | Rust, white corrosion, damaged coating, corrosion at cut edges and bolt holes | Rust spreading, coating gone, corrosion where metals touch |
Drainage and ground | Water standing near the foundations, erosion, vegetation growth | Water pooling, soil loss, plants shading or loading the structure |
After installation. Do a first check soon after the system is installed and has been through a few weeks of temperature and weather cycles, because bolts can settle in the early period.
Every year. Do a routine check of the full list above, ideally at the same time each year so that results can be compared.
After severe weather. After strong winds, heavy snow, flooding, or an earthquake, check the structure as soon as it is safe to do so.
When something changes. If modules are replaced, work is done on the array, or ground works take place nearby, check the affected parts.
These are general principles. Follow your project's operation and maintenance plan, the structure maker's instructions, and any requirement from the owner or insurer for the exact intervals.
Environment | What needs extra attention |
|---|---|
Coastal | Corrosion at coatings, cut edges, bolts, and earth connections |
Desert and dusty | Wear on coatings from blown sand, dust buildup, and thermal movement |
Snow and cold | Snow load effects, ice, frost heave of foundations, and bolt tightness after freeze and thaw |
Wet and agricultural sites | Standing water, soil erosion, vegetation growth, and animals |
Windy sites | Bolt loosening and fatigue at joints and clamps |
Keep a record. Note the date, the section checked, what was found, and what was done, with photos where useful.
Grade the findings. Sort issues into safety or structural concerns that need quick action, issues to fix at the next planned visit, and items to watch.
Retighten and replace. Retighten bolts to the torque specified by the structure maker, and replace missing, damaged, or corroded parts with parts of the same or better specification.
Repair the coating. Clean and treat damaged areas with a suitable protective coating before rust spreads, as the maker recommends.
Ask the maker when unsure. For cracks, deformation, or foundation movement, get the supplier or a qualified engineer to assess the structure before it is put back to use.
Loose bolts: vibration, thermal movement, or fasteners that were not tightened to the specified torque at installation
Coating damage: scratches during handling, cutting or drilling on site, or wear from sand and water
Foundation movement: soil conditions different from the design, water erosion, or frost
Earth connection failure: corrosion or loose connections, especially where different metals meet
Module clamp slip: wrong clamp position, insufficient tightening, or wind movement
A solar mounting system holds up the whole array, and it works in conditions that wear it down slowly. A first check after installation, a routine annual check, and an extra check after severe weather catch most problems early. Record what you find, fix issues in order of risk, and follow the structure maker's torque and repair instructions. Final intervals and procedures should follow your project's operation and maintenance plan.
A common approach is a first check soon after installation, a routine check every year, and an extra check after severe weather. The exact intervals should follow your project's operation and maintenance plan and the maker's instructions.
They should be checked, because vibration and temperature changes can loosen them, especially in the first months. Retighten to the torque specified by the structure maker, and replace any damaged fasteners.
Loose fasteners, coating damage that leads to corrosion, and foundation movement are among the most common. Regular inspection finds them before they affect the structure or the modules.
Planning a solar project and want a structure built for long service life? Browse our ground, roof, and carport solar mounting systems, or contact us with your site, loads, and environment, and we will quote a system with installation and maintenance guidance.
Whatsapp: +86-18823394830