NEW
Home » News » Installation & Design » Solar Mounting Grounding and Bonding: Rails, Modules and Earth Connections

Solar Mounting Grounding and Bonding: Rails, Modules and Earth Connections

Views: 0     Author: Site Editor     Publish Time: 2026-10-30      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
telegram sharing button
sharethis sharing button

Solar Mounting Grounding and Bonding: Rails, Modules and Earth Connections

A solar mounting structure must be bonded so that every metal part of the array, including the rails, the module frames, and the support posts, is electrically connected, and the whole array must be connected to the earthing system. Without this, a fault can leave metal parts live, and the protection devices may not trip. Bonding does not happen on its own: painted, anodized, or coated surfaces insulate, and joints between different metals can lose contact over time. This guide explains what needs to be bonded, how the connections are usually made, how metal pairings affect corrosion, and what to check before you buy and install.

pv-module-frame-to-rail-bonding-connection.png

Quick Overview: What Gets Bonded in a Solar Array

Connection

What it joins

Common methods

Module to rail

Aluminum module frame to mounting rail

Bonding clamps, clips with piercing teeth, or a bonding jumper

Rail to rail

Neighboring rails and splices

Bonded splice, or a jumper across the joint

Rail to post or beam

Rails to the supporting structure

Bonded fasteners, or a jumper where the joint does not conduct

Row to row

Separate rows or tables

Bonding conductor between rows

Array to earth

The bonded structure to the earthing system

Grounding conductor to an earth electrode or the site grounding grid

Why Bonding Matters

The metal frame of a solar array is within reach of people and carries system voltage nearby. If a live conductor touches the frame, the frame needs a low-resistance path to earth so that the fault current can flow and the protection device can act. Bonding all metal parts together also keeps them at the same electrical potential, which reduces the risk of shock between parts. Bonding is a safety requirement in most projects, and the rules come from the project specification and the applicable electrical code and standards.

Bonding and lightning protection are different

Grounding and bonding deal with fault current and touch voltage. Lightning protection is a separate design that deals with direct strikes and surges, and it has its own components and rules. A bonded array does not mean the site has lightning protection, so ask the designer which one the project requires.

solar-rail-splice-bonding-jumper-diagram.png

How the Connections Are Made

Module frames to rails

Module frames are usually anodized aluminum. Anodizing is an insulating layer, so a plain clamp may not make good electrical contact. Bonding clamps and clips are built with teeth or other features that cut through the surface layer and make contact with the bare metal. Another approach is a separate bonding jumper from the frame to the rail. Check which method your module and mounting supplier have tested together, and follow the module manufacturer's installation instructions.

Rails and splices

A splice that is only bolted may not carry fault current reliably. Many systems use a splice designed to bond the rails, and others add a jumper across the joint. Ask the supplier whether the rail splice is tested as part of the bonding path, and what the supplier recommends where it is not.

Structure and earth

The bonded rails are connected to the supporting posts or beams, and then to the earthing system through a grounding conductor. The conductor size, the number of connection points, and the earth electrode design come from the project specification and the applicable code. On large sites, the array is usually tied into the site grounding grid.

solar-structure-to-earth-grounding-connection.png

Metals and Corrosion at Bonded Joints

A bonded joint joins two metals, and some pairs corrode when they touch in the presence of moisture. This is called galvanic corrosion, and it can slowly ruin the electrical contact that the bond depends on.

Metal pair

What to watch

Aluminum and galvanized steel

Often used together, but moisture can cause corrosion at the contact, so use suitable hardware and keep the joint dry where possible

Aluminum and copper

Strong galvanic effect, so avoid direct contact, or use connectors rated for both metals

Aluminum and stainless steel hardware

Common and generally accepted, but still check the guidance for your environment

Zinc-coated steel and bare steel

Cut edges and drilled holes lose their zinc and need protection

Use connectors and hardware that are rated for the metals they join, and avoid mixing hardware from different suppliers without checking compatibility. Our Aluminum vs Galvanized Steel Solar Mounting guide explains how the two materials compare more broadly.

galvanic-corrosion-metal-pair-bonding-chart.png

Installation Points to Check

  1. Follow the bonding plan in the drawings. The designer decides where the bonds, jumpers, and earth connections go, so do not skip or change them on site without approval.

  2. Use bonding hardware as designed. Install clamps and clips with the torque and orientation the manufacturer specifies, so the teeth bite through the surface.

  3. Bond across joints that do not conduct. Where a splice or bolted joint is not a tested bonding path, add a jumper.

  4. Treat cut and drilled areas. Field cuts and holes expose bare steel, so treat them as the manufacturer instructs.

  5. Keep conductors tidy and protected. Run grounding conductors so they are not pulled tight, rubbed, or left lying in standing water.

  6. Test continuity after installation. Check that the bonded array and the earth connection meet the project requirement, and record the results.

What to Confirm When You Buy

  1. The bonding method for modules, and whether the clamps or clips have been tested with your module frame.

  2. Whether the rail splices are part of the tested bonding path, or whether jumpers are needed.

  3. The standard the project follows, such as IEC 62548, UL 2703, or a local code, and what evidence the supplier can show.

  4. What is included in the quote, since bonding clips, jumpers, lugs, and grounding hardware may be listed separately.

  5. The material and finish of the hardware, so it suits the environment and the metals it touches.

Common Mistakes to Avoid

  1. Assuming the bolts bond the array, when painted or anodized surfaces insulate the joint.

  2. Leaving out bonding across splices and row-to-row connections.

  3. Mixing metals carelessly, such as copper lugs directly on aluminum, which can corrode the connection.

  4. Forgetting to treat cut edges on galvanized steel, which weakens both protection and contact.

  5. Skipping the continuity test, so a loose or missing bond goes unnoticed until a fault.

  6. Confusing bonding with lightning protection, and leaving the project without the design it actually needs.

Conclusion

A solar mounting structure is safe only when its metal parts are bonded together and connected to earth through joints that stay conductive for years. Plan the module, rail, structure, and earth connections as one system, use hardware designed for the metals involved, and test continuity after installation. Final requirements come from the project specification, the module manufacturer's instructions, and the applicable standards and codes. Our How to Install Solar Mounting Systems guide covers installation steps, and our Cable Tray Grounding and Bonding guide explains how the same ideas apply to cable tray.

FAQ

Do solar mounting structures have to be grounded?

In most projects, yes. The metal parts of the array are normally bonded together and connected to the earthing system so that a fault has a safe path to earth. The exact requirement comes from the project specification and the applicable electrical code.

Do anodized aluminum module frames need special bonding hardware?

Often yes. Anodizing is an insulating layer, so bonding clamps and clips are designed with teeth or other features that reach the bare metal, or a separate jumper is used. Follow the module manufacturer's installation instructions and the mounting supplier's tested method.

Is a grounded solar array also protected against lightning?

Not necessarily. Grounding and bonding deal with fault current and touch voltage, and lightning protection is a separate design with its own requirements. Ask the project designer whether lightning protection is required for your site.

Planning a solar project? Browse our ground solar mounting, roof solar mounting, and solar carport systems, or contact our team with your array layout, module type, and site conditions.

Shenzhen Wanan Industrial Co., Ltd. was established in 2004 and is a China-based manufacturer specializing in Cable Tray Systems and Solar PV Mounting Systems.We manufacture Perforated Cable Trays, Cable Ladders, Cable Trunking, HDG & ZAM Cable Trays, and customized cable management solutions, together with solar mounting systems for various PV projects.With 22+ years of manufacturing experience, we provide factory-direct supply, OEM/ODM services, and technical support to customers worldwide.

Quick Links

Products

Leave a Message
Contact Us
Please leave your message here, we will give you feedback in time.

ONLINE MESSAGE

  Phone : +86-18823394830
微信图片_20260601173007_87_6 Whatsapp: +86-18823394830
  Email : admin@szwaindustry.com
  Add : Room 17A01, Block 1, Yintai Building, No. 15 Huilong Road, Shengping Community, Longcheng Street, Longgang District, Shenzhen ,Guangdong , China
 
Copyright © 2026 Shenzhen Wanan Industrial Co., Ltd. All Rights Reserved.  Sitemap | Privacy Policy