NEW
Home » News » Installation & Design » Solar Mounting Foundations: Ground Screw vs Concrete Pile vs Ballast

Solar Mounting Foundations: Ground Screw vs Concrete Pile vs Ballast

Views: 0     Author: Site Editor     Publish Time: 2026-10-27      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
telegram sharing button
sharethis sharing button

Solar Mounting Foundations: Ground Screw vs Concrete Pile vs Ballast

The foundation is what anchors a solar mounting structure to the ground or roof, and the right type depends mainly on the soil or roof conditions, the design loads, and the schedule. Ground screws and driven piles install quickly and suit many ground-mount sites, concrete foundations suit sites that need high capacity or have difficult soil, and ballast suits flat roofs and sites where nothing can be driven into the surface. No type is best everywhere, so the choice should follow a site investigation, not habit or unit price alone. This guide compares the common options and explains what to confirm before you choose.

solar-foundation-four-types-cross-section-infographic.png

Quick Overview: Common Solar Mounting Foundation Types

Foundation type

How it works

Where it is commonly used

Ground screw

A steel screw pile is turned into the soil and holds the structure by the soil's grip on its thread

Many ground-mount sites with suitable soil; sites that need fast, low-disturbance installation

Driven pile

A steel section is driven into the ground, usually with a piling machine

Large ground-mount plants with suitable soil and a long, repeatable layout

Concrete pile or footing

Reinforced concrete is cast in a bored hole or a formed footing

Difficult soil, high loads, or sites where driven foundations are not suitable

Ballast

Concrete blocks or other weights hold the structure down by their own weight

Flat roofs, landfills, and sites where the surface cannot be penetrated

Ground Screw Foundations

A ground screw is a steel pile with a helical thread that is turned into the ground. It needs no concrete and no curing time, so installation is fast and the structure can often be fixed to it right away. Because it disturbs the site very little, it suits land where the owner wants to limit excavation, and screws can often be removed at the end of the project. Whether a ground screw works depends on the soil: very hard ground or buried obstacles can stop installation, and very soft ground may need longer or larger screws.

Points to confirm

  • That the soil allows the screw to be installed to the required depth without refusal

  • That a pull-out and lateral load test has confirmed the capacity the design assumes

  • That the screw material and coating suit the soil's corrosion conditions

Driven Pile Foundations

A driven pile is a steel section, such as an H-section, C-section, or tube, that is pushed into the ground with a piling machine. It is common on large ground-mount plants because the layout repeats and the machine can install many piles quickly. Like ground screws, it needs no concrete. It works best in soil that the machine can penetrate, and it can meet refusal in rocky or very hard ground, so the site should be checked first.

Points to confirm

  • That the soil allows driving to the design embedment depth

  • That the tolerance on position, height, and verticality suits the structure's design

  • That the steel coating is suited to the soil and groundwater conditions

Concrete Pile and Footing Foundations

Concrete foundations are cast in place in bored holes or formed footings, with steel reinforcement. They can be designed for high capacity and for ground where driving or screwing is not practical, such as rock close to the surface or soil with a lot of obstacles. They take longer to build because of excavation, forming, and curing, and they are harder to remove at the end of the project. They are also common for carports and other tall structures that carry high loads.

Points to confirm

  • The concrete grade, reinforcement, and embedment depth required by the structural design

  • The curing time allowed in the schedule

  • How the steel base plate or column is anchored into the concrete, and how its position is controlled

solar-mounting-foundation-wind-resistance-mechanism.png

Ballast Foundations

A ballast foundation holds the structure down with weight instead of anchoring it into the ground or roof. It is common on flat roofs where drilling through the waterproofing is not allowed, and on landfills or capped sites where the surface must not be penetrated. The main limit is weight: ballast adds load to the roof or ground, so the supporting structure must be able to carry it, and the amount needed rises with wind load. Ballast is also not suited to every site, for example steep or windy locations with low weight allowance.

Points to confirm

  • That the roof or ground can carry the added weight, based on a structural check

  • That the wind load assumptions match the site (see our Solar Mounting Wind Load and Snow Load guide)

  • Whether the ballast can be reduced with mechanical anchors where the roof allows them

solar-foundation-site-conditions-selection-guide.png

How Soil and Site Conditions Affect the Choice

Site condition

What it affects

Soft or loose soil

May need longer screws or piles, or a different foundation type

Rock or very hard ground

Can stop driving or screwing, and may call for drilled concrete foundations

High groundwater

Affects corrosion, concrete work, and capacity

Frost or seasonal ground movement

Embedment depth and design must account for it

Corrosive soil

Needs a suitable coating or material for buried steel

Roof with limited load capacity

Limits how much ballast the roof can carry

What to Tell the Supplier

  1. Site location and soil report, if one exists, so the foundation type can be matched to the ground.

  2. Design wind and snow loads, since uplift and overturning decide the foundation size.

  3. Test results, such as pull-out and lateral load tests, if the site has been tested.

  4. Roof details, including structure, load capacity, and whether penetrations are allowed.

  5. Schedule and access, since installation speed and equipment access affect the choice.

  6. Whether the foundation must be removable at the end of the project.

Common Mistakes to Avoid

  1. Choosing the foundation before a site investigation, then finding refusal or weak soil during installation.

  2. Comparing only the unit price, without counting installation time, equipment, and the cost of rework.

  3. Skipping load tests and assuming the design capacity from a general soil description.

  4. Adding ballast to a roof without checking that the roof can carry it.

  5. Ignoring corrosion on buried steel in aggressive soil.

solar-foundation-information-for-supplier-checklist.png

Conclusion

Ground screws, driven piles, concrete foundations, and ballast each fit different sites, and the right choice follows the soil or roof conditions, the design loads, and the schedule. A site investigation and load tests are what turn a good guess into a reliable foundation design, and they are far cheaper than rework after installation. Give your supplier the site information, the loads, and the schedule up front, and have the final foundation design confirmed by a qualified structural or geotechnical engineer. Our Solar Mounting System Price Guide explains how foundation choices affect the overall quote, and our How to Install Solar Mounting Systems guide covers installation steps.

FAQ

Which solar mounting foundation is cheapest?

It depends on the site. Ground screws and driven piles often cost less in installation time and equipment on suitable soil, while concrete costs more in labor and curing time. Ballast avoids penetrating the surface but adds weight and material. Compare the total installed cost, not just the price of the foundation parts.

Do I need a soil test before choosing a foundation?

For ground-mount projects, yes, in almost all cases. A soil report, and ideally pull-out and lateral load tests, shows whether a screw or pile will reach the required depth and capacity. Without it, the foundation may fail to install or may not meet the design loads.

Can a solar mounting foundation be removed at the end of the project?

Ground screws and driven piles can often be removed more easily than concrete, and ballast can be taken away. Concrete foundations are harder to remove. If removal matters for your project, tell the supplier early, since it can change the foundation type.

Planning a ground-mount project? Browse our ground solar mounting, roof solar mounting, and solar carport systems, or contact our team with your site conditions, loads, and array size.

Shenzhen Wanan Industrial Co., Ltd. was established in 2004 and is a China-based manufacturer specializing in Cable Tray Systems and Solar PV Mounting Systems.We manufacture Perforated Cable Trays, Cable Ladders, Cable Trunking, HDG & ZAM Cable Trays, and customized cable management solutions, together with solar mounting systems for various PV projects.With 22+ years of manufacturing experience, we provide factory-direct supply, OEM/ODM services, and technical support to customers worldwide.

Quick Links

Products

Leave a Message
Contact Us
Please leave your message here, we will give you feedback in time.

ONLINE MESSAGE

  Phone : +86-18823394830
微信图片_20260601173007_87_6 Whatsapp: +86-18823394830
  Email : admin@szwaindustry.com
  Add : Room 17A01, Block 1, Yintai Building, No. 15 Huilong Road, Shengping Community, Longcheng Street, Longgang District, Shenzhen ,Guangdong , China
 
Copyright © 2026 Shenzhen Wanan Industrial Co., Ltd. All Rights Reserved.  Sitemap | Privacy Policy